Toilet shopping is a must if you plan to give your washroom a complete makeover. After getting the best toilet from many options available, your next concern should be its installation. No worries. To Install a toilet is no big deal; you can do it on your own without any professional assistance. But, if you are doing it for the first time, it can be a little frustrating if you are not aware of the process.
That’s where we come to your rescue. We will guide you through the installation process of the toilet and will answer your most asked question; How to Install a Toilet.
Steps to Install a Toilet
Steps in installing the toilet will vary if you are setting it in a completely new place as compared to replacing the old one. While replacing, you may not face as many issues because you may have an idea of problems you encounter. Besides, there are a few essential things that you don’t need to worry about while replacing. Yet, when it comes to installing a toilet, it requires patience and a little hard work.
Here are the few critical steps in detail that you can follow to install a toilet.
Know about your Toilet
First, you should be aware of your toilet and its parts. You must know what is going to come in a package and then prepare yourself for the installation. You don’t have time to learn about the details while installing. So, it is better that you have an overview beforehand. These are the necessary parts of the toilet that you should remember.
- Soil pipe
- Closet bolt
- Closet bend
- Seat bolts
- Closet flange
- Rubber tank-to-bowl washer
- Supply line
- Compression unit
- Compressing ring
- Rubber washer
- Flapper chain
- Wax ring
Undoubtedly, It would be helpful if you had a measurement of the distance from the wall to the floor bolts. Usually, standard toilets have a measure of 12inch from the walls. So, if your toilet meets the standard size, then you can comfortably fix the toilet to its place. Otherwise, you have to face a little difficulty.
It is better to get measurements before toilet shopping.
Prepare the floor
Stuff the rag in the soil pipe to trap the sewage gas and keep the hardware equipment from dropping. Then, check the hole in the floor if its large enough to entertain the closet flange right up to the collar. Dry the soil pipe and place the flange over it—finally, its time to measure the distance between the flange’s collar bottom and the floor. Make sure the flange’s collar rests on the floor, dry-fit the flange to the soil pipe, and then to the closet bend. If the flange is not tightened to the floor, then you should know its time to remove the wax ring and try again until it tightens.
Fasten the Stop Valve
First of all, make sure to shut-off the water supply line of the washroom. Remember to set any bucket under the supply line, the use a tubing cutter to sever the line. Also, while attaching the stop valve, it is recommended to leave about 1 inch of the pipe then remove the handle and stem of the valve. Moreover, use the rag to dry the pipe from inside and outside and then apply flux on each side.
Set the Bowl
Use the brass closet bolts and insert them into the flange’s collar slots and press the wax ring on it. After that, lift the bowl and align holes with the help of closet bolts. Instead of twisting, please press down the bowl on the wax ring until it rests on the floor. This particular step may annoy you as it demands several tries to get fit into the right place.
Installing a Tank
Ensure the seating of rubber tank-to-bowl washer from the outside of the tank. To insert the tank bolts, fit the small size diameters rubber tanks into the holes. Then, gently place the tank on the back of the bowl and slip a nylon washer on each of them—Hand-thread the nuts before dropping a nylon washer. Do not overtight the nuts as it may crack the porcelain, but do it until the tank is on the level. Finally, connect the handle of the tank to the flapper chain.
Time to Install Supply Line
Try to fit the stop valve and the tank supply fitting with the help of a tool. Hold the pipe and flared-end-up, then mark it half-inch between these points and below the outlet. Then, cut the supply line according to the mark.
In the last step, slip the plastic and compression nut and then the compression ring in the order on the supply line. Fit the compressing ring after seat the particular line in the outlet. Also, tight the plastic nuts of the supply line that are present under the tank and then tighten the compression nuts in the end.
Place the seat assembly and then put plastic bolts from the back of the seat and seat holes of the bowl. The next step is to tight the nuts by hand and start the supply line, open the valve, and start flushing to check its performance.
Finally, the installation guide of the toilet is ready for you. Follow the steps not to experience any inconvenience while setting up your new toilet. It wouldn’t consume much of your time and energy if you have done it back then, but if you are a novice, be prepared to invest your whole day in the installation.
Giving your house a new look may take your time, energy, and lots of research. But at the end of the day, it is worth it. We are leaving you with a complete guide of How to Install a Toilet that only helps you to replace your old toilet in your existing washroom, but assists you in setting up in a completely new and different place. It is an easy, simple, and cost-effective process. Also, do not forget to check out our article on the best toilets.
Also Read: How To Maintain Your Water Softening System?