It is the most asked question, how to replace a toilet flapper? Since toilet leaking is a common problem which is only caused by the old toilet flappers. If the flapper in your toilet has rubber material, then either it is break or leakage. In such a case, a new flapper needs to be installed. Flappers are not difficult to install and do not have a high cost. You can buy them and install them with ease.
Regarding how to replace toilet flapper, you need to follow these steps:
Steps of Replacing a Toilet Flapper
Removing the Old Flapper
First of all, you will need to remove the old flapper from your toilet. Regarding this, you have to stop the flow of water to the tank. So you have to shut off the valve from the lower part of the wall. It can be behind will or near beside the toilet. You have to turn the dial clockwise until it stops moving.
If you cannot turn off the valve by hand, you can spray it with a lubricant for 5 minutes and then twist the valve back and forth to loosen it. You will hear a trickling sound that means the batter is shuttering off. Those who don’t find the water valve can then disable the water from the house.
Empty the Tank
You have to lift off the toilet tank lid to empty the tank and set it aside carefully and flush the toilet so all the water will drain.
Disconnect the Bad Flapper Valve.
You will find a flapper over the hole. It has a large semicircular sheet that releases the water from the tank, and this way, you can connect in 2 places, such as the chain and the tiny pegs.
You have to unclip the chain to pull the edges out from the flapper so the pegs can be removed. However, you have to carefully do this because it can make the submerged components brittle.
On the other side, there are new flappers that come with a chain attached. If your flapper has a chain, then remove it from the flush lever.
Install the New Flapper
For this purpose, you have to buy a new flush valve seal. So you have to find the appropriate specifications when looking for a new one. You will find different shapes and sizes. Make sure you are getting the right one that covers your toilet’s flush valve.
Since they are made of different materials so, the best one is a standard rubber flapper. It costs a bit more, but you will get a secure seal.
After that, you have to connect the new flapper to the flush valve, so regarding this, you need to slide the holes on either side of the rubber seal over the pegs on the valve. Then you have to clip the lift chain to the lower end of the toilet to handle the lever. In this regard, you have to lower the flapper to confirm that it sits securely over the flush valve. You have to make sure about the connection sites.
Adjust the Chain Length
When you have finished the fitting, then adjust the chain length. You should be sure about the tension in the chain. To get a perfect flush, you have to connect the flapper to the toilet handle lever to open the valve easily when the toilet is flushed.
Test out the New Flapper
When all adjustments are made, you need to turn the water shutoff the valve counterclockwise to restore the water. For this, you have to refill the tank and wait for some moments, so the water level rises. Lastly, you don’t need to forget to replace the toilet tank lid to get high performance.
Keeping Flapper’s Condition Good
It is important to keep the toilet’s flapper in a good condition. When you notice something, you should replace it as soon as possible to avoid extra damage. Moreover, this way, let you save your bucks. It will be a simple and expensive way that’s why there is no reason to take care of it the right way. You should be pleased when you see the utility bills.
However, if there is a need to be prepared about the new flapper every 2-3 years.
Hire a PLumber
Last but not least, you should hire a professional to get done complicated repairs if you have problems. Remember that if you don’t have the necessary skills of plumbing that don’t install a flapper. It can lead to the worst experience. You should get an experienced plumber to get things done. They better understand the problems and diagnose them. Hence, you can solve all the water-related complications that prove baffling to the average homeowner.
FAQs
What Is A Toilet Flapper?
It is a small item that plays a role in the flushing mechanism. You can take it as a water stopper, just like in your bathtub. In the toilet, it also holds and stops the water.
How Do You Flush A Toilet Tank?
To flush a toilet tank, you have to follow these steps:
- Firstly, you have to turn off the water from the valve.
- You can find it near your toilet or floor beneath the toilet tank.
- Then you need to remove the lid from the toilet tank.
- After that, you have to flush the toilet to empty the water from the tank.
- Lastly, you need to ditch the flapper chain from the lever of the flush. That’s all.
The Conclusion
All in all, you have gone through how to replace a flapper. Now it would not be a headache to change the flapper anymore. You can easily do it by yourself since it is not difficult. Hence, you can now say goodbye to slow lead and phantom flushes. Besides that, if you have any questions, then you can comment below.
Leave a Reply